Back to the SWTPA home page




In Memoriam

Membership Form

Why join the SWTPA?

The Pullers



The SWTPA Sledge


Contact us

Tractor Pulling History

History of US Pulling

It is said around the 1900's when farming machines were pulled by horse that farmers would boast about how strong their horses were. They would make big claims that their horse could tow large loads, such as a fully loaded hay cart or wagon. To prove this for their neighbors, farmers would challenge one another to contests to prove who had the strongest horse. So a barn door was removed and laid flat on the ground the horse was then hooked up to it and the farmer ushered the horse to drag the barn door along the ground. One by one people jumped on the door until the horse was no longer able to drag it, the horse that pulled the most people the greatest distance was the strongest. This event called draft horse pulling is still carried out today with specially bred horses trained to have high strength and low stamina, but instead of people fixed weights on sleds are dragged as far as possible. Whilst is often said that the term horsepower is derived from this event, in reality the term was coined by James Watt when he invented the steam engine.

Draft Horses Pulling the 'sledge'

It wasn't until 1929 that motorized vehicles were put to use in the first events at Bowling Green, Missouri and Vaughansville, Ohio. The sport was recognized from this time but didn't really takeoff until the 50's and 60's when it was finally realised that there were no uniform set of rules. The rules from state to state, county to county were all different and competitors never knew what standards to follow which made the sport very hard to grasp for any new comers. Finally in 1969 representatives from eight different states got together to create a uniform book of rules to give the sport the structure that was needed and created the National Tractor Pullers Association. The NTPA's early years were events that used standard farm vehicles with the motto "Pull on Sunday, plow on Monday" and it stayed basically the same way through the 70's with only stock and modified tractors. Stock tractors were the commercially available tractors made by well known manufactures and modified tractors were the basic tractor chassis with another non tractor engine mounted on it.

Allis-Chalmers 'WD' pulling in 1957

Tractors stayed single engine until a couple of Ohio brothers introduced the crossbox which could allow multiple engines to be attached to a single driveshaft. After this it was usual to see modified tractors with four engines while the stock tractors tried to catch up by adding intercooled turbochargers but both still retained the appearance of a tractor. Soon tractors became single use machines that were not used on the farm making the "Pull on Sunday, plow on Monday" motto a part of history.

Starlight Express III

Throughout the 70's and 80's the modified division continued to thrill the crowds adding more and more engines and very soon the tractors lost their tractor look and turned into high spec dragsters. The limit was finally reached in 1988 when a tractor with seven engines was produced. As well as piston engines jet engines made an appearance in 1974 with a four jet engined one appearing in 1989. The growing popularity of this sport created a new division in 1976 called four wheel drive which immediately caught a great fan base. The engines in these vehicles kept on growing and growing from 450 cubic inches/7.3 litres up to 700/11.5 and probably would have carried on but the NTPA capped it at 650/10.6 naturally aspirated and no blown engine in 1989. Blown engines were allowed but only in the new 1986 division of two wheel drives or "funny cars" as the NTPA called them.

Two other divisions were made: the pro-stock and the mini-modified division which was a garden lawn mower mounted with a supercharged V8, These divisions aren't usually seen nowadays leaving four divisions to the present day two wheel drive, four wheel drive, stock tractors and modified tractors.

the sledge

In the early days two main techniques were used either a dead weight of fixed mass was dragged along or the step on method where people stood at fixed positions and stepped on as the sled came past. Another rule which has now been dropped was that a speed limit should be observed because they found the people who where stepping on were getting their ankles and legs twisted or broken from the increased speed at which they had to step on. Today's tractors can achieve theoretical speeds of more than 125mph.

The Sledge Total Friction

Today's sleds use a more complex system of gears to move weights of up to 65 000 pounds/29 000 kilograms. They way in which it does this is to start off with all the weights over the sleds rear axles to give it and effective weight of the sled and plus zero. As the tractor makes its way up the course the weights are pushed forward of the sleds axles pulling the front of the sled into the ground synthetically creating a gain in weight until the tractor is no longer able to overcome the force of friction.

Source: Wikipedia (for full article and sources click here)

History of UK Pulling

The first official pull was held at The Royal Show Stoneleigh 1978. In 1977 Mark Osborne got his father to build a sledge and Tractor. This sledge was latter owned by Mike Lawrence and re-named the Decision Maker and operated in the South West.

Most people that get involved in Tractor Pulling come from Farming or Agricultural Engineering Industries, Plant Hire or Transport. They are driven by the need to demonstrate their abilities, showing how to squeeze more power out of any given engine, using their ingenuity and skill to put together a stronger balanced Tractor, that they are able to control along a measured length of track faster and farther than the next person. This goes to show mans natural competitive nature to be the best that he can be.

Sorry, this section is still under construction...

History of the SWTPA

Sorry, this section is still under construction...